The last major strike was in November 2014, which decimated the antenna and it’s radom
covering, and even managed to weld the antenna base to the support pipe at the top of the tower.
This was duly replaced with a new Co-linear antenna, along with a new cable tail and this
successfully returned the system back to normal.
However – as time passed noise began appearing on weaker signals being received due to electrical disturbances in the tower structure with the vibration caused by high winds and other deteriorating hardware on the tower. We had several attempts to fix the situation but we neverwere able to get a permanent fix, and as we want to extend the functions of the repeater with a remote HF outpost at Mt Beevor, this would mean that extra link antennas would be required.
The tower was inspected by a fully licensed rigger, who got to the second level before he
condemned the tower as unsafe and expressed the view that it was a miracle that the tower was still standing. He took photos of items that seemed beyond redemption, such as section bolts that had rusted with no threads and nuts that had disintegrated and almost non existent, as per the examples below.
It was decided to try and get the tower to a state where it could be lowered to the ground
without any damage to property, personnel and the antennas on the tower. This would allow us towork on the structure at ground level and repair and restore it to a fully fit structure that will give service for at least another 25 years into the future.
The owner of the property was not really interested in refurbishing the tower himself, as he is of advanced years and does not really care it had to be removed for safety reasons. The tower location is really exceptional and gives us good primary service area for a radius of some 160km ranging out in some areas to 260Km depending on propagation on the day.
This meant that the various users had tocome up with the money to fund this project and then approach the land owner for his permission to do this, this was subsequently done and permission was received. Iapproached the Committee and spoke at Club meetings about what needed to be done and approval was given to go ahead with this, the other interested parties have alsoagreed to share costs so the project is avaiable one.
To lower the tower meant that it wouldneed to be made as safe as we could make it and a crane organised to pick it up off itsmountings and lay it over on blocks on the ground. Several crane firms were contacted, but the clear contender was Nick’s cranes asthey had a suitable mobile unit and personnel to do the work. To ensure that the tower was going to bestable for the removal, required some very careful work by riggers to replace critical bolts in the tower structure. This work was done by carefully working up from the ground and replacing those nuts and bolts essential to the structure of the tower, a potentially hazardous job, but one that was done well.
The next move was to provide a continuation of services, this meant that a temporary mast was erected to carry the commercial repeater and a temporary relocation of the VK5RAD repeater to another site at Summertown, this work when completed allowed us to remove all the cables from the equipment and roll them up to be fixed to the tower for retrieval during the repair process.
The tower was duly secured by the chains and ready to be lifted off, so Dean and myself got busy and removed the securing bolts on the three legs, these had not been removed since the early 70’s, so you can imagine that a lot of brute force and ignorance delivered by sledge hammers and punches was required to move them out of the mounting brackets in the concrete blocks at the base of the tower. Fortunately we had been putting lots of Penetrine and had loosened the nuts on previous days, so this made the work somewhat easier.
The work begins in earnest.
The tower will now need to be scraped down, and all the loose rust an old paint has to be
removed, all the bolts will be replaced and the various sections separated and the mounting pads checked for their integrity. There are bent sections of the mast from when it was dropped pre 1970’s that need to be checked and straightened. We will be using quarter power tools to accomplish this, in some cases the pipe or steel section may need to be replaced and checked for any fractures.
This is where our members come in – we need people to scrape, sand, and wire brush the
structure to remove all the old material, once that is done then the metal needs to be painted with rust converter (in this case phosphoric acid) so care will need to be taken and the correct protective equipment must be worn, such as safety glasses, gloves, protective overalls. To this end the Club will / has purchased disposable overalls, nitrile gloves (acid proof) and sets of safety glasses for those who will help in this project. If you have your own PPE gear, then it would assist us in this process. The type of tools required would be wire brushes, rotary wire wheels, spanners and shifters etc and anything that can be used to complement the job at hand. The tower is large, some 40 metres long and the legs about 3 – 4 metres apart at the base, so we are going to need plenty of people to assist us.
A new cable tray ladder is to be fitted to allow all cables (new and old) to be secured to the
tower in a proper manner, so that the vibration and personnel that are fitting and maintaining antenna’s etc will not damage them, lightening protection devices are to be fitted along withproper earthing of the tower to promote safety and longevity of equipment. Most cable to be refitted will be new, the main cables will be LDF5-50 thus providing very low loss and better performance of the systems on site. New antenna’s for the remote HF site project and a new main professional multi band array at the tower top for our Amateur services are to be fitted.
We will of course be limited by the vagaries of the weather, so there will be days when no
work can be performed or some that may get cut short, and we do not want to burden those older members with strenuous tasks, so the more the merrier. Once the tower has been cleaned, repaired and rust converted and primed, it will be ready for the main 2 pack epoxy coating to go on.
This will be performed by a commercial company that specializes in this type of work, they
assure us that the coating will last for a minimum of 20 years in this sort of environment, so that makes us feel that the job in hand is worth it.
A time line is being generated for the repairs, this will be circulated around all members on
a regular basis, if you can help us, then please volunteer some of your time so we can get this back in service ASAP.
I will send updated circulars to all members with photos and information of what has
happened so far, there will also be a map as to the location of the site. Please be aware that as this is on private property, so we do not want persons to randomly enter the property, but you will be welcome on work days when a supervisor is on site.
Please send your contact details to Trevor Molde VK5NIX, preferably by email to :-
firstname.lastname@example.org or phone: 82350634 and leave a message. Trevor has asked that you make sure you identify you message as being for AHARS so it does not get lost in his junk mail.
Thanks Barry VK5BW.
Clean rust, paint, etc off, replace bolts, rust convert and prime surfaces ready for coating.